Gossen SI 232-II Manuale Utente Pagina 25
- Pagina / 28
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
GOSSEN METRAWATT GMBH 25
9 Memory Adapter Technical Data
Supported Measuring Instruments
METRAHit 12S ... 16S, 16I/T, 18S, 14A, 22S/M ... 29S
Operating Elements and Operation
7 segment LCD display and 4 keys.
Almost all parameters can be configured manually, or with a PC via the interface.
Memory
128 kB CMOS memory with battery backup.
Measurement value storage in accordance with the differential value method (compressed)
with adjustable hysteresis. An average of 50,000, and at least 20,000 measurement values
are acquired depending upon whether or not significant signal changes or time spans occur
between the individual measurements. A maximum of 100,000 measurement values are
acquired if only minimal signal changes occur, if the sampling rate is equal to or less than
0.5 s and if hysteresis has been set to ALL.
Real-Time Clock
Real-time clock with battery backup. Max. error: 0.5 minutes per month
Interface
To the Multimeter Optical receiver/transmitter, 950 nm wavelength,
8192 / 9600 baud, 8 bits, no parity, 1 stop bit
To the PC Bidirectional, adjustable baud rate: 9600, 19,200 or 38,400
baud, 8 bits, no parity, 1 stop bit
Number of Adapters Up to10 data memory adapters can be interconnected.
The maximum number depends upon the selected sampling
rate for online PC data acquisition:
With METRAHit 1x
up to 6 adapters at a baud rate of 19.2 kBd
up to 4 adapters at a baud rate of 9.6 kBd
With METRAHit 2x
up to 3 adapters at a sampling rate of 50 ms
up to 8 adapters at a sampling rate of 200 ms
Connections Pin 9 is used for the synchronization of interconnected adapt-
ers in the PC operating mode.
Pins 4 and 7 must be connected to high level at the PC and are
used to supply electrical power to the data memory adapter.
Power is drawn from this source by the data memory adapter
for levels of down to 5 V. Power is drawn from the battery for
lesser voltage levels.
Pin 3 (PC-TXD) is used for negative level generation of the PC-
RDX signal from the RS232 interface.
With the exception of pin 1 and pin 9 (used for synchroniza-
tion), all of the interface conductors are looped through to
additional data memory adapters.
- Operating Instructions 1
- 3-348-636-02 1
- 2 GOSSEN METRAWATT GMBH 2
- GOSSEN METRAWATT GMBH 3 3
- 3.1 General Information 4
- GOSSEN METRAWATT GMBH 5 5
- 6 GOSSEN METRAWATT GMBH 6
- 4.1 Connecting the Adapter 7
- 8 GOSSEN METRAWATT GMBH 8
- 21.978 mA 9
- 5.2 Display 10
- 5.4 Replacing the Batteries 11
- key twice 12
- key as well 12
- • Select Normal Operation 13
- 6.4 Menus Overview 14
- 7.1 Set Sampling Rate – rAtE 15
- 7.2 Set Hysteresis – HYSt 15
- 7 Menu Item Descriptions 15
- 7.3 Trigger Settings – triG 16
- • Disabling the Trigger 17
- hh:mm 18
- on OFF 18
- dd hh:mm 18
- ModEM no YES 18
- StorE ...) 19
- Start manual data recording: 20
- • Interrupt Data Recording 20
- Select primary value 21
- Select recording time 21
- • Internal Memory Test 23
- 8 METRAwin 10 24
- 8.1 Installing METRAwin 10 24
- 8.3 Starting METRAwin 10 24
- GOSSEN METRAWATT GMBH 25 25
- Power Supply: 26
- Electrical Safety 26
- Mechanical Design 26
- 11 Product Support 27
ActiveForever Pride Go Go Elite Traveller Plus Electric Scooter manuali
Manuali dei proprietari e guide per l'utente per Motocicli ActiveForever Pride Go Go Elite Traveller Plus Electric Scooter.
We fornisce 1 manuali pdf ActiveForever Pride Go Go Elite Traveller Plus Electric Scooter per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Commenti su questo manuale